First steps in RF hacking

2016-09-20 18:05:00

The first part of my current project that I wanted to tackle, was the "RF hacking" part: capturing, analyzing, modifying and replaying the radio signals sent and received by a hardware device.

Home alarm systems (or home automation systems in general) often used one of two RF bands: 433MHz or 868Mhz. As far as I understand it, 433MHz is often used by lower end or cheaper systems; haven't figured out why just yet. In the case of the Kerui G19 alarm, the adverts from the get-go tell you it uses 433MHz for its communications.

Cracking open one of the remotes I find one basic IC in there, the HS1527 (datasheet). The datasheet calls it an "OTP encoder", but I haven't figured out what OTP stands for in this case. I know "OTP" as "One Time Password" and that's also what the datasheet hints at ("HS1527 hai a maximum of 20 bits providing up to 1 million codes.It can reduce any code collision and unauthorized code scanning possibilities.") but can't be that because the Kerui remotes send out the exact same code every time. has a short discussion on the HS1527, calling it a "learning code" as opposed to a "fixed code" (e.g. PT2262), but the only difference I see is 'security through obscurity', because it simply provides a large address space. There is no OTP going on here!

The datasheet does provide useful information on how its bit patterns are generated and what they look like on the output. The four buttons on the remote are tied 1:1 to the K0 through K3 inputs, so even if HS1527 can generate 16 unique codes, the remote will only make four unless you're really fast. 

After that I spent a lot of time reading various resources on RF sniffing and on 433MHz communications. Stuff like LeetUpload's articles, this article on Random Nerd, and of course lots of information at Great Scott Gadgets. Based on my reading, I put together a nice shopping list:

And cue more learning! 

GQRX turns out to be quite user-friendly and while hard to master, isn't too hard to get a start with. It's even included with the Kali Linux distribution! Using GQRX I quickly confirmed that the remotes and control panel do indeed communicate around the 433MHz band, with the panel being at a slighly higher frequency than the remotes. With some tweaking and poking, I found the remote to use AM modulation without resorting to any odd trickery.

GQRX dilligently gave me a WAV file that can be easily inspected in Audacity. Inspecting the WAV files indicated that each button-press on the remote would send out multiple repeats of the same bitstream. Zooming into the individual bitstreams you can make out the various patterns in the signal, but I'd had problem matching it to the HS1527 datasheet for the longest of times. For starters, I never saw a preamble, I counted 25 bits instead of 20+4 (address+data) and the last 4 bits showed patterns that should only occur when >1 button was pressed. 

Then it hit me: that 25th bit is the preamble! The preamble is sent back-to-back with the preceding bitstream. Doh!

Just by looking at the GQRX capture in Audacity, I can tell that the address of this particular remote is 10000100001100110001 and that 0010 is the data used for the "disarm" signal. 

Time for the next part of this experiment; let's break out the Arduino! Again, the Arduino IDE turns out to be part of the Kali Linux distro! Awesome! Some Googling led me to Suat Özgür's RC-Switch library, which comes with a set of exemplary programs that work out-of-the-box with the 433Mhz transceivers I bought. 

Using the receiver and sniffing the "disarm" signal confirms my earlier findings:

Decimal: 8663826 (24Bit) Binary: 100001000011001100010010 Tri-State: not applicable PulseLength: 297 microseconds Protocol: 1

Raw data: 9228,864,320,272,916,268,920,272,912,276,908,872,308,284,904,280,904,280,912,276,904,872,320,868,312,280,908,276,912,868,312,876,324,276,900,276,908,280,908,876,312,280,908,280,904,880,312,276,908,

Decimal: 8663826 (24Bit) Binary: 100001000011001100010010 Tri-State: not applicable PulseLength: 297 microseconds Protocol: 1

Raw data: 14424,76,316,280,904,288,896,280,904,20,1432,36,1104,36,912,280,904,284,900,280,908,876,312,872,308,280,908,88,272,120,928,128,756,24,224,20,572,44,1012,32,800,24,188,32,964,68,1008,44,856,

The bitstream matches what I saw in Audacity. Using Suat's online parsing tool renders an image very similar to what we saw before.

So, what happens if we plug that same bitstream into the basic transmission program from RC-Switch? Let me show you!

If the YouTube clip doesn't show up: I press the "arm" button on the alarm system, while the Arduino in the backgrouns is sending out two "disarm" signals every 20 seconds. 

To sum it up: the Kerui G19 alarm system is 100% vulnerable to very simple replay attacks. If I were to install this system in my home, then I would never use the remote controls and I would de-register any remote that's tied to the system. tags: , ,

View or add comments (curr. 0)